Serves as Cat. 5 distribution Device (DD) as required by ANSI/TIA/EIA.
Accommodates up to 4 incoming phone lines.
Allows up to 48 Outlet cables or phone home runs (12 for each incoming line).
Insulation Displacing connectors (IDC) for use with "punch down" tools.
Economical solution for residential and commercial installations.
Dimensions: 7.25" by 5.5" by 1" molded engineering grade plastic.
Includes identifier labels and mounting screws.
Patent Pending.
Made in U.S.A.
DD2 Phone system Cat. 5E Rated Distribution Device
For use with 110 Punch Down Tool.
Cat. 5E RATED as required by ANSI/TIA/EIA.
Internally bridged - No bridging clips required.
Designed for consistent repetitive wiring.
Designed to be wired form the back for clean organized appearance.
Expandable and versatile to accommodate any phone system wiring configuration.
Includes mounting screws and a set of 10 labels for organizing and wiring any
Phone System Combination.
The DD2 simplifies wiring, adding, changing, and identifying voice/data/security lines.
Dimensions 6.25" by 6"
Patent pending.
Made in U.S.A.
DD3 Cat. 5E Residential/SOHO Phone Distribution Block
For use with standard 110 Punch Down Tool.
Cat. 5E RATED as required by ANSI/TIA/EIA.
Accommodates up to 4 incoming phone lines.
Allows up to 48 Outlet cables or phone home runs (12 for each incoming line).
Internally bridged - No bridging clips required.
Designed for consistent repetitive wiring.
Stands 1" off mounting board to be wired form the back for clean organized appearance.
Includes mounting screws and labels for organizing and wiring any
Phone System Combination.
Dimensions 6.25" by 6"
Patent pending.
Made in U.S.A.
DD3K
DD3 With the DD110T Push Down Tool
3C
Cover for DD3 or DD2 Phone Distribution Device
DD3C
DD3 Distribution Device and 3C Cover
DD3CK
DD3 Distribution Device, 3C Cover, and DD110T Push Down Tool.
DD3CX
DD3 Distribution Device, 3C Cover, and X4 4-Way Video Splitter.
DD3CXN
DD3 Distribution Device, 3C Cover, X4 4-Way Video Splitter, and Data Network Card.
DD5 Structured Wiring Center
Modular design enables customization for each housing requirement.
Designed for use with ETCON DD1 (Cat. 5) or the DD3 (Cat. 5E). The most efficient 110 phone
distribution block on the market.
Allows up to 96 stations or phone home runs (24 for each incoming line) with additional
phone block.
Includes 8 Video Outputs (5-2050 MHz)
Custom Enclosure with open top and bottom for easy wiring and for future requirements.
Keyholed cover for quick and easy surface or flush mount installation.
Enclosure designed with extra positions to accommodate additional modules as needed.
Completely modular and upgradeable for future requirements. (Phone, Video and Data Module Available)
Dimensions 14 1/4 X 15 X 3 1/2.
DD5 Includes
DD1 - Cat. 5 Phone Block.
X8 - 8-way video splitter
Enclosure.
Cover.
DD5E Includes
DD3 - Cat. 5E Phone Block.
X8 - 8-way video splitter
Enclosure.
Cover.
DD110T Push Down Tool
Designed for use with ETCON DD1, DD2, DD3, and 110 blocks.
Made in U.S.A.
CX1
Installation tool for mounting F (coax) connectors.
Pushes back coax shielding.
Mounts connector on coax wire over coax shielding to proper depth
Eliminates sore fingers.
Belt or shirt pocket clip.
Made in U.S.A.
X4 4-way Video Splitter
SPR1 Snap Ring
Single gang low voltage mounting bracket.
Made in U.S.A.
SPR2 Snap Ring
Double gang low voltage mounting bracket.
Made in U.S.A.
SPR3 Snap Ring Extender
Single and Double gang low voltage mounting bracket.
Made in U.S.A.
SPR4 Pre-Wire Strap
SKCX Splice Kit
Direct burial splice for RG6, RG11 RG59 coax wire, 2-4 pair telephone wire.
